Fiber to the premises [FTTP]

Fiber to the premises (FTTP) is a form of fiber-optic communication delivery in which an optical fiber is run directly onto the customers' premises. This contrasts with other fiber-optic communication delivery strategies such as fiber to the node (FTTN), fiber to the curb (FTTC), or hybrid fibre-coaxial (HFC), all of which depend upon more traditional methods such as copper wires or coaxial cable for "last mile" delivery.
Fiber to the premises can be further categorized according to where the optical fiber ends:
FTTH (fiber to the home) is a form of fiber optic communication delivery in which the optical signal reaches the end user's living or office space.
An optical signal is distributed from the central office over an optical distribution network (ODN). At the endpoints of this network, devices called optical network terminals (ONTs) convert the optical signal into an electrical signal. (For FTTP architectures, these ONTs are located on private property.) The signal usually travels electrically between the ONT and the end-users' devices.


Optical portion
Optical distribution networks have several competing technologies.

Direct fiber


The simplest optical distribution network can be called direct fiber. In this architecture, each fiber leaving the central office goes to exactly one customer. Such networks can provide excellent bandwidth since each customer gets their own dedicated fiber extending all the way to the central office. However, this approach is extremely costly due to the amount of fiber and central office machinery required. It is usually used only in instances where the service area is very small and close to the central office.

Shared fiber


More commonly each fiber leaving the central office is actually shared by many customers. It is not until such a fiber gets relatively close to the customers that it is split into individual customer-specific fibers. There are two competing optical distribution network architectures which achieve this split: active optical networks (AONs) and passive optical networks (PONs)..


Optical fiber is used by many telecommunications companies to transmit telephone signals, Internet communication, and cable television signals. Due to much lower attenuation and interference, optical fiber has large advantages over existing copper wire in long-distance and high-demand applications. However, infrastructure development within cities was relatively difficult and time-consuming, and fiber-optic systems were complex and expensive to install and operate. Due to these difficulties, fiber-optic communication systems have primarily been installed in long-distance applications, where they can be used to their full transmission capacity, offsetting the increased cost. Since the year 2000, the prices for fiber-optic communications have dropped considerably. The price for rolling out fiber to the home has currently become more cost-effective than that of rolling out a copper based network. Prices have dropped to $850 per subscriber in the US and lower in countries like The Netherlands, where digging costs are low.
Since 1990, when optical-amplification systems became commercially available, the telecommunications industry has laid a vast network of intercity and transoceanic fiber communication lines. By 2002, an intercontinental network of 250,000 km of submarine communications cable with a capacity of 2.56 Tb/s was completed, and although specific network capacities are privileged information, telecommunications investment reports indicate that network capacity has increased dramatically since 2002.
The need for reliable long-distance communication systems has existed since antiquity. Over time, the sophistication of these systems has gradually improved, from smoke signals to telegraphs and finally to the first coaxial cable, put into service in 1940. As these communication systems improved, certain fundamental limitations presented themselves. Electrical systems were limited by their small repeater spacing (the distance a signal can propagate before attenuation requires the signal to be amplified), and the bit rate of microwave systems was limited by their carrier frequency. In the second half of the twentieth century, it was realized that an optical carrier of information would have a significant advantage over the existing electrical and microwave carrier signals.
In 1966 Kao and Hockham proposed optical fibres at STC Laboratories (STL), Harlow, when they showed that the losses of 1000 db/km in existing glass (compared to 5-10 db/km in coaxial cable) was due to contaminants, which could potentially be removed.
The development of lasers in the 1960s solved the first problem of a light source, further development of high-quality optical fiber was needed as a solution to the second. Optical fiber was finally developed in 1970 by Corning Glass Works with attenuation low enough for communication purposes (about 20dB/km), and at the same time GaAs semiconductor lasers were developed that were compact and therefore suitable for fiber-optic communication systems.
After a period of intensive research from 1975 to 1980, the first commercial fiber-optic communication system was developed, which operated at a wavelength around 0.8 µm and used GaAs semiconductor lasers. This first generation system operated at a bit rate of 45 Mbit/s with repeater spacing of up to 10 km.
On 22 April, 1977, General Telephone and Electronics sent the first live telephone traffic through fiber optics, at 6 Mbit/s, in Long Beach, California.
The second generation of fiber-optic communication was developed for commercial use in the early 1980s, operated at 1.3 µm, and used InGaAsP semiconductor lasers. Although these systems were initially limited by dispersion, in 1981 the single-mode fiber was revealed to greatly improve system performance. By 1987, these systems were operating at bit rates of up to 1.7 Gb/s with repeater spacing up to 50 km.
The first transatlantic telephone cable to use optical fiber was TAT-8, based on Desurvire optimized laser amplification technology. It went into operation in 1988.
TAT-8 was developed as the first undersea fiber optic link between the United States and Europe. TAT-8 is more than 3,000 nautical miles (5,600 km) in length and was the first transatlantic cable to use optical fibers. It was designed to handle a mix of information. When inaugurated, it had an estimated lifetime in excess of 20 years. TAT-8 was the first of a new class of cables, even though it had already been used in long-distance land and short-distance undersea operations. Its installation was preceded by extensive deep-water experiments and trials conducted in the early 1980s to demonstrate the project's feasibility.
Third-generation fiber-optic systems operated at 1.55 µm and had loss of about 0.2 dB/km. They achieved this despite earlier difficulties with pulse-spreading at that wavelength using conventional InGaAsP semiconductor lasers. Scientists overcame this difficulty by using dispersion-shifted fibers designed to have minimal dispersion at 1.55 µm or by limiting the laser spectrum to a single longitudinal mode. These developments eventually allowed 3rd generation systems to operate commercially at 2.5 Gbit/s with repeater spacing in excess of 100 km.
The fourth generation of fiber-optic communication systems used optical amplification to reduce the need for repeaters and wavelength-division multiplexing to increase fiber capacity. These two improvements caused a revolution that resulted in the doubling of system capacity every 6 months starting in 1992 until a bit rate of 10 Tb/s was reached by 2001. Recently, bit-rates of up to 14 Tbit/s have been reached over a single 160 km line using optical amplifiers.
The focus of development for the fifth generation of fiber-optic communications is on extending the wavelength range over which a WDM system can operate. The conventional wavelength window, known as the C band, covers the wavelength range 1.53-1.57 µm, and the new dry fiber has a low-loss window promising an extension of that range to 1.30 to 1.65 µm. Other developments include the concept of "optical solitons, " pulses that preserve their shape by counteracting the effects of dispersion with the nonlinear effects of the fiber by using pulses of a specific shape.
In the late 1990s through 2000, the fiber optic communication industry became associated with the dot-com bubble. Industry promoters, and research companies such as KMI and RHK predicted vast increases in demand for communications bandwidth due to increased use of the Internet, and commercialization of various bandwidth-intensive consumer services, such as video on demand. Internet protocol data traffic was said to be increasing exponentially, and at a faster rate than integrated circuit complexity had increased under Moore's Law. From the bust of the dot-com bubble through 2006, however, the main trend in the industry has been consolidation of firms and offshoring of manufacturing to reduce costs.

Technology

Modern fiber-optic communication systems generally include an optical transmitter to convert an electrical signal into an optical signal to send into the optical fiber, a cable containing bundles of multiple optical fibers that is routed through underground conduits and buildings, multiple kinds of amplifiers, and an optical receiver to recover the signal as an electrical signal. The information transmitted is typically digital information generated by computers, telephone systems, and cable television companies.